This guide explains how the camera’s two high-brightness white LEDs support full-colour night capture, shows daytime and dark-room images, and walks through setup, positioning and common night-recording problems.
How Full-Colour Night Capture Works
When light is insufficient, two white LEDs beside the lens illuminate the scene so the camera can record colour detail. This helps distinguish the colours of objects and their surroundings after dark. The LEDs emit visible white light, so consider whether illumination is suitable for the people or wildlife at your installation site.

See the Daytime and Night Results
The examples below show colour capture in daylight and in a room with its lights switched off and on.
Daytime Full Colour
The riverside image shows buildings, vegetation and water in daylight.

Dark Room: Room Lights Off
The orange chair, red decoration and green plant leaves remain visible in colour with the room lights switched off.

Dark Room: Room Lights On
The room-light-on image provides a colour reference for the same indoor objects under ceiling lighting.

Set Up Night Photography
Start with the camera in SETUP so you can change settings and review test recordings before unattended use.
- Prepare power and storage. Check battery charge and insert a compatible memory card with the camera switched OFF. Back up existing files before formatting; formatting erases the card.
- Select capture mode. Move the switch to SETUP and choose Photo, Video or Photo + Video. Set the date and time so recordings are easy to identify.
- Set the fill light. Open Fill Light Intensity and start with Auto. Medium and Low provide alternative brightness settings; Off disables supplementary light.
- Choose the trigger. For motion-triggered capture, use PIR Motion Detection and leave TimeLapse disabled. Time-lapse recording instead captures at the selected interval and disables ordinary PIR triggering.
- Make a night test. Aim at the intended subject area, take a short test after dark and review colour, brightness and moving-subject detail. Adjust the light setting or position if needed.
- Begin unattended recording. Save the settings, close the case and port covers, switch to ON and allow the startup countdown before leaving the detection area.
Improve Colour and Detail at Night
Position the camera so its light reaches the subject area without nearby objects dominating the frame. Test in the actual night conditions rather than relying only on a daytime setup check.
- Avoid glare: clear nearby branches and keep walls, glass, metal and other reflective surfaces out of the immediate light path.
- Balance brightness: if close objects look washed out, try a lower fill-light setting or reposition the camera farther from them.
- Check distant subjects: if the intended subject is dark, move the observation area closer and review the fill-light setting.
- Keep the view clear: clean the lens and LED windows gently and check for condensation or obstructions.
- Test movement: review a walking subject as well as a stationary scene; motion can reduce recorded detail.
Common Night-Capture Problems
Use the checks below before changing multiple settings at once. Make one adjustment, record another test and compare the result.
| Symptom | What to check |
|---|---|
| Night image is too dark | Check battery charge, confirm Fill Light Intensity is not Off, clean the LED windows and move the subject area closer. Test Auto and the available brightness settings. |
| Close objects appear too bright | Lower the fill-light setting, increase separation from the nearest objects and remove reflective surfaces from the light path. |
| White LEDs do not illuminate | Test under dark conditions, check that supplementary light is enabled and verify battery charge. In Auto, daylight may not require supplementary illumination. |
| Camera does not trigger | Confirm the switch is ON, the memory card has space, the monitoring period includes the current time and TimeLapse is disabled for ordinary PIR operation. Check aim and PIR sensitivity. |
| Night recordings stop or become shorter | Check battery charge and storage capacity. Recharge or replace the appropriate power source for the installed hardware version. |
| Battery drains quickly | Frequent triggers, white-light use and long clips increase consumption. Shorten clips or increase PIR Detection Delay as appropriate, and remove moving vegetation that causes unwanted triggers. |
View and Download Recordings
Use WILDLIFE CAM for nearby preview, settings and file access through Bluetooth-assisted Wi-Fi. Enable phone Bluetooth and Wi-Fi, add or select the camera in the app and accept the prompt to join its network. Keep the phone within local wireless range. For full-size file review, copy JPG photos and MP4 videos from the memory card or use the USB data connection. Back up recordings before deleting files or formatting the card.
Quick Settings Reference
| Night illumination | Two high-brightness visible white LEDs |
|---|---|
| Capture modes | Photo / Video / Photo + Video |
| Fill Light Intensity | Auto / Medium / Low / Off |
| PIR sensitivity | High / Medium / Low |
| PIR Detection Delay | 5 seconds–60 minutes; default 10 seconds |
| Time lapse | Interval capture; ordinary PIR triggering is disabled while enabled |
| File types | JPG photos / MP4 videos |
| App | WILDLIFE CAM for nearby camera access |