Setup and operation guide for the XINBAI H90 cellular wildlife camera. Follow the supplied hardware version and manual.
Before Installation
This guide follows the supplied XINBAI H90 bilingual manual. Confirm the correct European or North American LTE hardware version for the destination carrier. Prepare a valid SIM with active data, a microSD card up to 512GB (Class 10 or faster recommended), and twelve matching 1.5V AA batteries. Turn the camera OFF before fitting cards, batteries or external modules.

Power, Card and Antenna Setup
Fit the 4G antenna and GPS module in their correct positions without forcing the connectors. Install all twelve batteries with correct polarity. Insert the SIM and microSD according to the marked orientation. Without a memory card the manual says the camera cannot store data or enter monitoring mode. Back up card files before formatting: all stored data will be permanently deleted. If using external power, use a compatible DC9.0V/2A adapter with the correct plug and marked polarity; the adapter is not supplied.

TEST Mode and Local Recording
Switch to TEST. Set date/time and select Photo, Video or Photo & Video. Press MENU to open settings, use arrows to select an item and OK to confirm. Photo series options are1,2,3 or10; clip length is3 seconds to10 minutes. Choose a resolution suitable for storage and battery needs. Maximum photo output is36MP; native sensor resolution is not established by the manual. The video menu includes3840×2160, but no frame rate is specified.
Select Cellular Version
The manual lists European LTE-FDD B1/B3/B7/B8/B20/B28 and North American LTE-FDD B2/B4/B5/B12/B13/B25/B26. These are separate hardware variants, not a promise of worldwide compatibility. Ask the carrier or supplier to confirm band and service support before deployment. SIM data allowance, service validity and sufficient signal are needed for uploads.
Add the Camera in TrailCam_4G
Use the app identified in the supplied manual and register an account. Keep the phone connected to the internet. With the camera in TEST, wait for cellular signal bars instead of X. GPS needs a suitable outdoor location; the icon changes when a fix is acquired. In the camera MENU, open IMEI to display its QR code. In the app choose Add device, scan the camera IMEI, enter the requested device name and binding information, then add it to the device list. Do not publish your actual IMEI QR code in shared documentation.
Enable Uploads
In the camera menu set4G Switch toON. Choose File Upload Frequency: Real time, Specific time orOff. Start with Standard upload mode to reduce data and battery consumption. High Definition uses more data and may take longer. Switch toON; after the15-second countdown the camera enters automatic standby. A detected animal can trigger capture and upload. Enable app notifications if upload alerts are required. The manual gives an approximate upload time, not a guaranteed response time.
Understand Cloud Previews
The cloud album displays uploaded files. For video, the manual describes a GIF containing one frame from the beginning, middle and end of the clip, not the full original video. Copy original recordings from microSD or USB. Remote settings are applied on the next camera wake-up or file upload, so a change may not appear immediately. In TEST playback, Upload current file can send a selected file manually.

Position and Test Motion Detection
Mount around1m above ground and aim toward the wildlife route. In TEST, move across the detection area and observe the indicators: green for an enabled side sensor and red for the main sensor. Adjust direction before switching toON. Choose Low, Middle orHigh sensitivity and Shot Lag from5 seconds to60 minutes according to the environment. GPS requires outdoor position acquisition.
Time Lapse and Recording Hours
Target Recording Time limits recording to a daily start/stop window. Time Lapse offers Normal, TL Video andOff. TL Video interval is5 minutes to24 hours; its output settings are1080P or720P, separate from ordinary video settings. Enabling time lapse deactivates motion sensors according to the manual. Turn it off for PIR triggering.
GPS Track and Account Binding
When GPS positioning succeeds, location can be stored in photo attributes. GPS Track compares position and can trigger a photo andSMS movement notification as described in the manual. Service and signal conditions affect operation. One camera can be bound to only one account: unbind it under My/My Device in the original account before binding elsewhere.
Mounting and File Care
Before drilling, check for electrical wiring and water/heating pipes. The supplied wall plugs are intended for concrete or stone; use fixings suitable for the actual surface. Back up recordings regularly. Endless Capture deletes the oldest files when storage is nearly full. For USB transfer, connect the supplied cable and copy files from the DCIM folder on the removable drive. Do not assumeUSB charges installed batteries.
Troubleshooting
For failed uploads, check4G Switch, upload frequency, SIM data/service validity, coverage, batteries and phone notifications. For GPS failure, test outdoors with a clearer sky view. For binding failure, check whether the camera remains linked to another account. If remote settings appear unchanged, wait for the next wake/upload. Do not disassemble the camera. The manual warns that a forgotten power-on password may require firmware service; contact support before attempting resets or firmware changes.